![]() ![]() Do not forget to clean the needles as well. Remove the water reservoir and clean it thoroughly. At times it might be a result of scale.įix this issue by descaling the machine. This is commonly caused by the presence of debris in the water valves. Problem: The Keurig is pumping water continuously If there isn’t any other barrier, your machine should get back to work. Once done and fully dry, place the parts back in place. Take out the reservoir then clean the metal mesh by washing it. The bottom of the water reservoir could have debris especially after using the machine for quite a long time. You should now be able to see the machine do what it says.Ħ. Run another test to see if the problem is sorted.Make sure you follow the proper descaling procedure so as not to miss out on any single step.Next, you might want to descale the machine to ensure that the water sucking tubes are also clean.Check the puncture needle and ensure it is well cleaned.It’s possible that there is a water blockage. Try running the machine without a pod to see if there is water running.But if that fails and it continues to power on, then it is a mechanical issue, so move to the next steps. Do the following įor an electrical fault – simply unplug the machine then allow it to rest for a short time then plug it back in. Your coffee maker is either experiencing some mechanical or electrical problems. ![]() Problem: Keurig says brewing but nothing comes outĪt times your Keurig may say brewing but nothing comes out. You can also read other users tricks at the ifixit website. Your machine should have responded the fix and start brewing coffee in normal quantity. The next step is to put them back together and then run several cycles of water minus the K-cup.Use the paper clip to clean all of them as well Next, under the handle lid, you should see a set of tubes that injects water into the K-cups.Using your paper clip, insert it into the tube and try to dislodge any remains of whichever beverage you’ve been brewing.You’ll then see a small metal tube(needle) that pokes a hole into the bottom of the K-cup.Take out the plastic holder that holds the K-cup in the brewer.Have your paper clip tool ready? Do the following This is just an extension of what you’ve been doing above but this time around your attention is concentrated somewhere. If your Keurig machine does not get back to brewing coffee, then you should advance to the next possible fix.Ĥ. This should remove any scale from the needle. Brew using this mixture, and run a few more cycles with regular water to flush everything out. Descale your Keurig using a mix of water and vinegar.Problem: clogged needle(s) due to scaleĭid you know that your Keurig has a needle that punctures the K-Cup’s foil lid? These needles get clogged with coffee grounds or minerals in the water.Īs a result, your coffee maker won’t brew a full cup or will give no coffee at all.įollow the following procedure to easily fix this problem: Get things back in order then try brewing againģ.You should then spank it several times so that any coffee grounds can be bumped out of the machine. Turn it upside down to pour out as much water as possible. This is done over the sink after removing the water reservoir and drip tray. Check the water reservoir and readjust it.If this works the other way round, then there is a fault somewhere. ![]() The water in the reservoir has to heat first before the pump to elevate it. ![]() Problem: The pump is not working correctlyĪs we said earlier, the machine working mechanism has been designed in such a way that certain parts must communicate or work in a specific order for it to brew. If the machine brews but keeps shutting off and on again, then you should confirm that you didn’t set the auto-shutoff feature.Ģ.Your coffee maker should start brewing again.You could just start by trying to run water alone in the first cycle to see what happens. After ensuring that the water reservoir is well placed, give it another shot.This causes the Keurig to power down as it doesn’t sense the presence of water. Note that the reservoir has a magnet and that might have been misplaced. Take out the water reservoir and place it back properly.Unplug the machine from the wall socket.To check whether this is the cause of your Keurig not brewing, do the following The Keurig machine is designed in such a way that, when the existing contacts in it fail, the whole system stops functioning. The first thing you should check is whether everything is where it should be. Problem: Some parts are not aligned correctly Keurig Troubleshooting: Common Problems and Solutions My Keurig wont brew 1. 1.4 Keurig Duo troubleshooting(stuck on descale).1.2 Keurig not pumping water or dispensing.1 Keurig Troubleshooting: Common Problems and Solutions. ![]()
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |